DIY Orelo (Orelo/Orelino)
by Bert 
, Tuesday, January 22, 2013, 21:23 (4111 days ago) @ Atilsley
Can you expand a little re your last point about 800hz xover and throat.
I would have throat 170mm wide x the height of the half cabinet (1000mm?).
Yes, 1000mm or a bit higher/lower depending on your preference having the midrange located.
Throat is 170mm wide as it equals the 2x 850cm2 of the used BD15 drivers giving the throat of the wave guide the same starting area.
Can you also clarify aporox driver hole cut out sizes. For altec, I may follow the VOTT A5 or similar, but your input appreciated.
Just make these as tall as you can (the inner edge of the frame), the width equals the width of the horns throat.
Bert
--
BD-Design - Only the Best!
Complete thread:
- DIY Orelo - BS, 2012-11-05, 11:26
![[*]](themes/default/images/complete_thread.png "Open whole thread")
- DIY Orelo - Bert, 2012-11-05, 19:52
- I like the look of the "half" Orelo in your pic... - samoore, 2012-11-12, 19:24
- It works well too... - Bert, 2012-11-12, 19:49
- It works well too... - Gasper, 2012-11-12, 20:59
- It works well too... - Bert, 2012-11-13, 00:14
- It works well too... - Gasper, 2012-11-12, 20:59
- It works well too... - Bert, 2012-11-12, 19:49
- DIY Orelo - anubisgrau, 2012-11-14, 09:44
- DIY Orelo - Rudy81, 2013-03-22, 07:26
- I like the look of the "half" Orelo in your pic... - samoore, 2012-11-12, 19:24
- DIY Orelo - DeMarko, 2013-01-09, 01:29
- DIY Orelo - Atilsley, 2013-01-21, 07:18
- DIY Orelo - Bert, 2013-01-22, 10:24
- DIY Orelo - Atilsley, 2013-01-22, 21:08
- DIY Orelo - Bert, 2013-01-22, 21:23
- DIY Orelo - Atilsley, 2013-01-23, 02:46
- 360mm to be exact... (nt) - Bert, 2013-01-23, 14:15
- 360mm to be exact... - Atilsley, 2013-01-28, 10:36
- 360mm to be exact... - Bert, 2013-01-28, 21:29
- 360mm to be exact... - Atilsley, 2013-01-31, 12:54
- 360mm to be exact... - Atilsley, 2013-02-02, 00:32
- 360mm to be exact... - Bert, 2013-02-02, 20:24
- 360mm to be exact... - Bert, 2013-02-02, 20:23
- 360mm to be exact... - Atilsley, 2013-02-02, 00:32
- 360mm to be exact... - Atilsley, 2013-01-31, 12:54
- 360mm to be exact... - Bert, 2013-01-28, 21:29
- 360mm to be exact... - Atilsley, 2013-01-28, 10:36
- 360mm to be exact... (nt) - Bert, 2013-01-23, 14:15
- DIY Orelo - Atilsley, 2013-01-23, 02:46
- DIY Orelo - Bert, 2013-01-22, 21:23
- DIY Orelo - Atilsley, 2013-01-22, 21:08
- DIY Orelo - Atilsley, 2013-02-11, 11:21
- DIY Orelo - Bert, 2013-01-22, 10:24
- DIY Orelo - Bert, 2012-11-05, 19:52