360mm to be exact... (Orelo/Orelino)
Bert, I know we touched on this before...but I'm trying to make an important decision on the xover point. I can get my horns down to about 800Hz...but preferred option is 1200Hz.
The Altec 416's have no problems goin to 1200Hz...but want to make sure the Oriels will cater for this higher point.
Regards.
Andrew
Complete thread:
- DIY Orelo - BS, 2012-11-05, 11:26
- DIY Orelo - Bert, 2012-11-05, 19:52
- I like the look of the "half" Orelo in your pic... - samoore, 2012-11-12, 19:24
- It works well too... - Bert, 2012-11-12, 19:49
- It works well too... - Gasper, 2012-11-12, 20:59
- It works well too... - Bert, 2012-11-13, 00:14
- It works well too... - Gasper, 2012-11-12, 20:59
- It works well too... - Bert, 2012-11-12, 19:49
- DIY Orelo - anubisgrau, 2012-11-14, 09:44
- DIY Orelo - Rudy81, 2013-03-22, 07:26
- I like the look of the "half" Orelo in your pic... - samoore, 2012-11-12, 19:24
- DIY Orelo - DeMarko, 2013-01-09, 01:29
- DIY Orelo - Atilsley, 2013-01-21, 07:18
- DIY Orelo - Bert, 2013-01-22, 10:24
- DIY Orelo - Atilsley, 2013-01-22, 21:08
- DIY Orelo - Bert, 2013-01-22, 21:23
- DIY Orelo - Atilsley, 2013-01-23, 02:46
- 360mm to be exact... (nt) - Bert, 2013-01-23, 14:15
- 360mm to be exact... - Atilsley, 2013-01-28, 10:36
- 360mm to be exact... - Bert, 2013-01-28, 21:29
- 360mm to be exact... - Atilsley, 2013-01-31, 12:54
- 360mm to be exact... - Atilsley, 2013-02-02, 00:32
- 360mm to be exact... - Bert, 2013-02-02, 20:24
- 360mm to be exact... - Bert, 2013-02-02, 20:23
- 360mm to be exact... - Atilsley, 2013-02-02, 00:32
- 360mm to be exact... - Atilsley, 2013-01-31, 12:54
- 360mm to be exact... - Bert, 2013-01-28, 21:29
- 360mm to be exact... - Atilsley, 2013-01-28, 10:36
- 360mm to be exact... (nt) - Bert, 2013-01-23, 14:15
- DIY Orelo - Atilsley, 2013-01-23, 02:46
- DIY Orelo - Bert, 2013-01-22, 21:23
- DIY Orelo - Atilsley, 2013-01-22, 21:08
- DIY Orelo - Atilsley, 2013-02-11, 11:21
- DIY Orelo - Bert, 2013-01-22, 10:24
- DIY Orelo - Bert, 2012-11-05, 19:52